Whole toilet layout
Show the WC, cistern feed, nearby wall, floor and obstruction clearance so the hose reach and holder position can be assessed.
Bidet Spray Installation Service in Singapore
Quick answer
FixMove provides bidet spray installation service in Singapore for compatible replacements and new or altered connection assessments. Send a wide toilet photo, close-ups of the cistern feed and shut-off valve, the bidet model or product link, preferred holder position and postal code. We then quote the named fittings, drilling, accessible leak check and applicable plumbing route. Price, timing and warranty apply only when confirmed in the accepted written scope.
A spray head, hose, tee, valve and wall holder are separate parts. The safe quote depends on what already exists, whether water can be isolated, the selected product and whether the proposal remains simple replacement work or alters the plumbing connection.
Replacement versus new bidet spray connection
| Site condition | Suitable first scope | Can be included when quoted | Important exclusions or checks |
|---|---|---|---|
| Existing spray head leaks but hose and connection appear serviceable | Compatible head replacement | Named head, washers, fitting and accessible leak observation | Hose, valve, tee, wall fitting and concealed leak unless listed |
| Existing flexible hose leaks or is damaged | Compatible hose replacement | Named hose, washers, removal, fitting and accessible leak observation | Pressure cause, head, valve or damaged thread beyond the listed scope |
| Full existing spray set is being replaced like for like | Set replacement after compatibility check | Head, hose, holder and existing compatible connection when itemised | New valve or tee, drilling, pipe alteration and finish repair unless named |
| No spray connection exists at the toilet | Connection assessment before price | Approved compatible connector or valve, route, holder and testing as quoted | Assuming a generic tee is permitted, suitable or compliant at every site |
| Valve is seized, corroded, leaking or inaccessible | Valve and isolation assessment first | Named valve work and isolation plan when feasible and quoted | Concealed pipe failure, building shutdown, wall opening or common-property work |
What a complete bidet quote packet shows
Valve and connection close-ups
Photograph the shut-off valve, existing tee or branch, hose threads, corrosion, water marks and any active leak from more than one angle.
Product evidence
Send the brand, model, product link, included fittings, instructions and whether FixMove or the customer is expected to supply the spray set.
Mounting surface
Identify tile, grout, wall panel, cabinet or a no-drill preference, plus the approved holder position and any known concealed service route.
Isolation and property type
State HDB, condominium, landed or commercial premises; whether the local valve works; and whether management or landlord approval is needed.
Existing fault history
Explain whether the problem is a drip, burst hose, loose holder, weak flow or new installation, when it occurs and what was previously changed.
Inclusions, exclusions and responsibility
- Supply responsibility: name the spray, hose, holder, valve, tee, adapters and washers supplied by each party; product compatibility and manufacturer warranty are not implied.
- Connection scope: identify the exact existing water point, proposed fitting, shut-off method and whether any valve replacement or pipe alteration is included.
- Mounting: state the holder position and no-drill or drilling method. Tile drilling, concealed-service risk, waterproofing and making good need explicit boundaries.
- Testing: define the accessible connection and operating check after installation. It is not a guarantee against future hose failure, misuse or concealed pipe defects.
- Customer preparation: clear the toilet area, provide access, disclose active leaks and obtain landlord or management approval where required.
- Commercial terms: require an itemised S$ total, planned attendance basis, variation rule, disposal if needed and written workmanship or supplied-part warranty terms if any.
Bidet spray installation process
Send photos and the product model
Include the entire toilet, close-ups of the valve and feed, the spray set or link, holder position, property type and postal code.
Classify replacement or alteration
Confirm whether this is head-only, hose-only, like-for-like set replacement, valve work or a new connection that needs a different plumbing route.
Agree every included component
List who supplies each product and fitting, connection and mounting method, drilling, removal, leak observation, exclusions and variation approval.
Confirm the suitable work route and slot
Check isolation, product compatibility, access and applicable PUB Licensed Plumber requirements before confirming timing.
Review the installed scope
Check the quoted connections and operation, receive care guidance, and keep only the written warranty terms that were accepted.
Singapore plumbing and HDB checks
PUB says regulated water-service and sanitary plumbing works must be carried out by a PUB Licensed Plumber, except simple plumbing works. Whether a bidet job qualifies as simple replacement work depends on the actual connection and proposal; a new or altered branch should not be described as a hose-only installation. See the PUB Plumbing Works requirements.
For HDB homes, do not drill or alter a connection from a generic assumption about concealed services. Confirm the actual proposal against the current HDB water and sanitary plumbing guidelines, plus any landlord or building rules that apply.
A particular connector, valve, check device or product label is not promised by this page. The quote should name the selected product and required fittings only after compatibility, applicable standards and site conditions are checked.
Bidet spray installation FAQ
How much does bidet spray installation cost in Singapore?
There is no responsible fixed S$ price before the existing connection, valve condition, product and mounting surface are checked. The quote should state whether the spray set is supplied or customer-supplied, every included fitting, drilling, removal, accessible leak check, exclusions, planned attendance basis and written warranty terms if any.
Can you replace only a leaking bidet hose or spray head?
A like-for-like hose or spray-head replacement may be suitable when the thread, pressure rating, condition and leak source are confirmed. If the valve, tee, wall connection or concealed pipe is also leaking or damaged, that is a different scope and must be quoted separately.
Is a new valve or tee connector included?
Only when the accepted quote names the compatible valve or connector and how it will be installed. A generic tee should not be assumed suitable for every cistern feed or water point; existing valve condition, available isolation, thread, clearance and applicable backflow requirements must be checked.
Do you install customer-supplied bidet sprays?
Customer-supplied products can be assessed from the model, fittings, instructions and site photos. Compatibility, missing adapters, product defects and manufacturer warranty remain separate, and installation should proceed only after the quote records responsibility for extra parts or an unsuitable product.
Does bidet installation include drilling the toilet wall?
Only if the holder location, mounting method, substrate and drilling boundary are approved in the quote. Concealed pipes, waterproofing, tile damage risk, no-drill alternatives and landlord or HDB restrictions must be considered before drilling; tile or finish repair is not automatically included.
When is a PUB Licensed Plumber required for a bidet spray?
The requirement depends on whether the actual proposal is simple plumbing work or regulated water-service plumbing work. A new or altered connection should not be treated as a hose-only task; after assessment, the quote should identify the PUB Licensed Plumber scope and any applicable requirements where needed.
How long does bidet spray installation take?
The planned duration depends on whether it is a compatible replacement or a new connection, the shut-off and valve condition, missing parts, drilling, access and regulated-work route. A date or duration is confirmed only after the photos, model, postal code and accepted scope are reviewed.